Posted by Mark Oakley on 24th Jun 2016
With the ever growing popularity of Lava Stones being used in Fire Pits, and in particular the larger sizes, I was recently reminded whilst helping a client with an installation problem how important it is to install these large size rocks correctly in your fire pit.
In is a common and understandable misconception that a fire
pit burner works in the same manner as a domestic gas hob burner, but in fact that is not the case.
On an ordinary gas hob burner, the flame burns adjacent to where the gas exits the burner as is clearly shown in the image on the right.
However, a fire pit burner does not function this way.
In fact it is probably incorrect to refer to this item as a burner. A Gas Delivery System might be more accurate, because it is designed to deliver the gas, but the gas then percolates upwards through the fire glass / lava rock and it should not ignite until it more or less reaches the surface.
The important point here is that the flame does not burn adjacent to the burner, but rather a couple of inches directly above it.
The burner is in fact isolated from the flame by the fire glass / lava rock, as is well illustrated by the picture on the below. In fact the ‘burner’ is actually protected from the heat of the flame by the fire glass / lava rock, as illustrated in the picture below.
So How does this relate to Large Lava Stones and similar Fire Pit Media.
If you were to just insert large size stones into your fire pit, you would inevitably create cavities in, around and on top of the burner.
When you turn on the gas and light your fire pit these cavities would fill with gas and ignite, which in itself is not a good thing. But these cavities may be much closer or even in contact with the burner, and thus when the gas is ignited you would have a hot spot, and the burner is not protected by a layer of fire media as it should be.
Depending on how your stones sit, you may not even be aware that these hot spots exist!
In these circumstances, the very best that may happen, is that you burner will warp due to the excessive heat, and it may even burn holes into the burner, if the hot spot is close or in contact with it, rendering your burner unfit for purpose.
It is easy to avoid this situation once you are aware of it, and can possibly save you some money as well. No down side at all.
The simple solution is to create a ‘filler’ layer of small media around and above the burner, to ensure that no gaps or cavities are created. Then you can place your favorite Lava Stones on top of the filler as required. See the diagram below.
This theory applies to all fire pit media. You must ensure that the burner is covered with an even layer of small size, about 1/4 inch material, up to above the top of the burner.
Do remember though not to cover any spark ignition probes that may have installed in your fire pit tray
Your 11 Point Check List: 1. Check With Your Local Fire Dept. To discover which codes may apply to a gas fire pit installation in your area, and if the finished installation needs an inspection by the Fire Dept. ( Find Your Local Fire Dept. ) ( Failure to comply with the [...]
Flame Height One of the most common questions we get from clients is concerning the flame height of their gas fire pit. The two variations of this question are; "how do I ensure I get a good flame height" or, "why is my flame height so puny". I always prefer question 1, because it usually, but not always means that [...]
Now more than ever, backyards have become an extension of our living space, with fire pits as the most sought after accessory to help create the perfect outdoor living environment. However, with this rise in popularity comes an increase in fire related accidents and injuries. Fortunately, many of these can be prevented with awareness of [...]
GAS FIRE PIT MANUAL IGNITION SYSTEMS MATCH-LIT THIS IS THE MOST BASIC OF THE IGNITION SYSTEMS. THE USER OPENS THE GAS VALVE MANUALLY USING THE GAS VALVE KEY AND LIGHTS THE BURNER WITH A LONG MATCH. TO TURN OFF, YOU SIMPLY CLOSE THE GAS VALVE. SPARK IGNITION THIS IS THE NEXT STEP UP FROM THE MATCH-LIT SYSTEM. AN IGNITOR PROBE [...]
HOW TO BUILD A GAS FIRE PIT The first thing to do when considering a fire pit is to check your local code. There may be regulations that can greatly affect what you had in mind. It is a good idea to use the installation manual of your chosen gas fire pit kit (tray, burner, ignition system) [...]
Today I am very pleased to announce that at The Magic Of Fire we have just been appointed as a supplier of a great range of products, Firegear Outdoors.They have a wide range of products that include fire glass, with some great new colours, fire pit burners and trays with all the accessories that you [...]
GAS FIRE PITTHE BASICS TRAY SUPPORT/COLLAR THIS SHOULD BE MADE FROM NON-COMBUSTIBLE MATERIALS, STURDY AND LEVEL WITH PLENTY OF DRAINAGE. ACCESS FOR MAINTENANCE IS MADE EASIER IF IT IS REMOVABLE. FIRE GLASS OR LAVA ROCK IS THEN PLACED OVER THE TOP, HIDING BOTH IT AND THE BURNER TRAY.CAVITY DO NOT FILL CAVITY. THIS WILL HELP PREVENT OVERHEATING AND [...]
We all like to save money where we can, so much so that DIY'ing has become a multi billion dollar industry.However, there are times when perhaps it's better, read safer, to pay a little more and buy professionally made equipment. This is never more true than when dealing with gas. So unless your are a [...]